Online bass and subwoofer test

Bass and subwoofer test online

Play or download short bass tones and a 20–120 Hz sweep through the currently selected speaker, subwoofer or headphone output.

Play bass testsDownload WAVs

Reviewed 29 September 2026

Browser bass and subwoofer test

Test bass and subwoofer output

Lower the source, amplifier and output volume first. Start with a 60 Hz tone, then choose a sweep or step-down if needed.

Bass frequency tones

Choose one frequency for a two-second tone. Keep the volume low; small speakers may not reproduce the lowest tones.

20–120 Hz bass sweep

Play one rising sweep from 20 to 120 Hz over eight seconds. It stops automatically; changes in loudness are not a measurement.

Step-down listening sequence

Ten tones descend from 150 to 20 Hz in about 24 seconds. Press “I can’t hear it” at the first inaudible step to end the sequence and note the previous frequency. Keep the volume unchanged.

Ready to test

Start low, keep headphones off your ears for the first tone, and stop for discomfort, rattling or heavy distortion.

Quick answer: lower the volume, select the speaker or subwoofer you want to test, and begin with 60 Hz. Try nearby tones once, then use the sweep if needed. Do not increase the volume simply because a very low tone is quiet or absent.

Download bass and subwoofer test-tone WAV files

Use these original files when the target player has no convenient browser or when you need the same signal on another device. Each tone is a two-second mono sine wave at 5% of full scale with short fades. The sweep runs logarithmically from 20 Hz to 120 Hz over eight seconds at the same level.

Download 20–120 Hz sweep WAV

The WAVs cover individual tones and the rising sweep; there is no download of the ten-tone step-down sequence.

Files are mono, 16-bit PCM at 44.1 kHz and contain no speech, tracking, metadata or third-party audio. Start with the amplifier or device volume low; a downloaded file is not a calibration signal and must not be used to set amplifier gain without the equipment maker's procedure.

What this bass and subwoofer test does

The buttons ask the browser to generate sine tones from 20 to 120 Hz. The sweep changes the requested oscillator frequency continuously across that range. This can help you compare routing, audible output and repeatable rattles at the same device volume.

The page does not request microphone access, so it cannot measure sound-pressure level, frequency response, distortion or the lowest frequency your equipment reproduces. It is a playback reference, not calibrated test equipment. For a broadband comparison across the whole range, the pink noise generator plays a steady reference at the same device volume.

How to test a subwoofer or speaker safely

  1. Set the source, amplifier and powered speaker or subwoofer volume low before starting.
  2. Select the intended system output and disconnect Bluetooth devices you do not want to test.
  3. Begin with 60 Hz. If using headphones, keep them off your ears for the first tone.
  4. Play each nearby frequency once at the same settings. Stop for heavy distortion, mechanical knocking or an uncomfortable level.
  5. Run the sweep once if you need a continuous comparison, then confirm anything unusual with familiar audio and the equipment maker's setup guidance.

Can the browser test a subwoofer separately?

Only when the selected system route sends browser audio to that subwoofer. This page plays through the browser's default audio destination; it cannot select an LFE channel, bypass a receiver's crossover or bass management, or prove that a silent result is a failed subwoofer. To check the subwoofer (LFE) channel on its own, use a 5.1 surround test through a receiver that supports it. Confirm the operating system, receiver or interface output before interpreting the tones.

How to interpret the result

No sound at the lowest tones

This does not prove a fault. The selected output, speaker size, enclosure, amplifier, device processing, room and your hearing can all affect what is audible. Do not keep raising the volume to force a result.

A rattle repeats at one frequency

Lower the volume and repeat once. Check for a loose object or surface near the speaker, then compare familiar audio. This browser cannot tell whether the source is the room, enclosure, connection or driver.

The sweep changes in loudness

That is expected in an uncontrolled listening check. A browser tone and your ears do not provide a calibrated frequency-response measurement.

Nothing plays at any frequency

Check media volume and output routing, then use the speaker and sound test. If every app is silent, follow the operating system or device maker's audio troubleshooting.

What the step-down result means

The last step you hear depends on the speaker or headphones, the enclosure, where you sit in the room, device processing, the volume and your own hearing. Treat it as a listening comparison between setups, not a measurement of frequency response or a hearing test. Phones and laptop speakers usually stop well above subwoofer range, which is expected and not a fault; to check left and right output on a laptop, test your laptop's speakers with reference tones. If the bass sounds thin or weak on a stereo pair, check that both speakers are in phase, because out-of-phase speakers cancel bass.

Keep the level controlled

The World Health Organization advises limiting loud-sound exposure and keeping personal-device volume below 60% of maximum. That percentage is only a precaution: this page cannot know the actual acoustic level produced by your source, amplifier and output device. Begin lower, keep each tone short and stop for discomfort, pain or ringing.

Sources and technical references

For a configurable sweep outside the bass range, use the frequency sweep generator. For one exact frequency anywhere from 20 Hz to 20 kHz, use the online tone generator. For left/right channels and higher fixed references, use the online speaker and sound test. Testing subwoofer output is different from clearing a phone speaker: if recent liquid is the cause, use the water-eject tool instead.