Test your speakers
Start at a low media volume. Each button plays a short sine tone generated in this browser.
Left and right stereo test
Use these to check stereo routing. Some devices, accessibility settings and browsers may mix both channels together.
Reference frequencies
Compare whether the speaker reproduces each tone cleanly. Different loudness between frequencies is normal and is not a hearing or hardware diagnosis.
Ready to test
Start at a low volume. Keep speakers away from your ears. Stop if a tone is uncomfortable, harsh or distorted.
Quick answer: lower the volume, select the intended output, then play left, right and both. Each individual control should follow its label on a stereo route; the both-channel control sends the same reference to both sides. It is free, runs in your browser and needs no app or microphone; each control plays a 440 Hz reference tone. Run the guided sequence for one repeatable pass. This browser sound check is a listening comparison, not a hearing test or hardware diagnosis.
Test my speakers online: left and right checks
- Play left. On a stereo route, the signal should come from the left speaker or left earcup.
- Play right and identify the physical side that responds. If the labels appear reversed, confirm the output orientation and connections before changing wiring.
- Play both. The same reference is sent to both channels; a correctly placed stereo pair may create an apparent center image.
- Run the guided left-both-right sequence once. Repeat an unexpected result at the same low volume, then compare familiar audio through the same output.
If either single-channel control plays through both sides, check Mono Audio, spatial processing, the selected output and any adapter or receiver settings. A phone or single Bluetooth enclosure may intentionally combine the channels. This page reports the browser signal and cannot inspect physical wiring or identify a failed component. If left and right play through separate speakers, use the speaker phase test to compare how the pair sounds in phase and out of phase.
How to test iPhone speakers
To check the built-in output, disconnect headphones and external speakers, lower the media volume and run the left-both-right sequence above. If a channel is missing or both buttons sound alike, follow our iPhone balance and Mono Audio checks before assuming a speaker is broken. The controls send stereo channels; they do not select or diagnose an individual physical iPhone speaker. For calls-only problems, see the iPhone earpiece instructions.
How to run a speaker balance test
- Lower the volume, select the intended stereo output and place yourself midway between the left and right speakers when possible.
- Play both once. It sends the same reference to both channels; the apparent center position can still shift with speaker placement, room reflections and system settings.
- Run the balance sweep. The status moves from left through center to right and back. Listen for a smooth change rather than treating one exact perceived position as a pass/fail result.
- If one side stays absent or much quieter, repeat the individual left and right controls, then inspect the device's balance and Mono Audio settings and compare familiar audio.
A phone, single Bluetooth enclosure or mono route may play both channels from one physical position. This browser test cannot measure whether two speakers have equal acoustic output because it does not use a microphone, know the room or calibrate the hardware.
Choose the right audio test
Speaker wet? Start with the wet-phone guide or AirPods drying guide before testing. These tools provide listening references, not hardware diagnosis.
Download left and right speaker-test sounds
Need files for an offline player, television, car or another device with no convenient browser? These original three-second stereo WAV files use the same quiet 440 Hz sine reference as the channel controls above. They contain no speech, tracking or third-party audio.
Left channel WAV
440 Hz in the left channel; the right channel is silent. Stereo, 16-bit PCM, 44.1 kHz, approximately 529 KB.
Download left channelBoth channels WAV
The same 440 Hz reference in left and right. Stereo, 16-bit PCM, 44.1 kHz, approximately 529 KB.
Download both channelsRight channel WAV
440 Hz in the right channel; the left channel is silent. Stereo, 16-bit PCM, 44.1 kHz, approximately 529 KB.
Download right channelStart with the device volume low. The file name tells you which channel should play; if the device forces mono output, the left-only and right-only files may both come from the same physical speaker. For water-eject audio, use the separate speaker-cleaner WAV downloads, or play the tone in your browser with the SpeakerEject water eject tool.
How to test car speakers with a phone or WAV file
Park the vehicle before connecting a phone, choosing files or changing audio settings. Google’s Android Auto setup instructions require the car to be in Park during setup, and both Android Auto and CarPlay route supported phone media through the car audio system.
- With the vehicle stationary, lower the car-media volume and connect the phone through the route you normally use: Bluetooth, USB, Android Auto or CarPlay.
- Play both once and confirm the tone comes from the vehicle rather than the phone. If the browser is not available through the car interface, download the left, both and right WAV files above and use a supported media source.
- Set the car's left/right balance and front/rear fader to their centered positions. Play left, then right, and note which side responds.
- To check front versus rear speakers, use the vehicle's own fader control while the both-channel file or familiar music plays. A stereo browser file contains left and right channels only; it cannot address four car-speaker positions independently.
- Repeat anything unexpected at a lower volume and compare a familiar track. Consult the vehicle or head-unit manual before changing wiring, amplifier gain or equalizer settings.
How to test a Bluetooth speaker
- Charge and pair the Bluetooth speaker, then select it as the current media or sound output. A paired device is not always the active playback destination.
- Lower both the source-device volume and the speaker's own volume before starting.
- Play both once. If the sound comes from the intended Bluetooth speaker, run the left-both-right sequence and repeat any unexpected channel.
- If nothing plays, confirm the output selection and try familiar audio in another app before removing and pairing the device again.
A single Bluetooth enclosure may combine both channels, and some devices or system settings use mono playback. Hearing left, both and right from the same physical position does not by itself mean the speaker is faulty. A paired stereo set should be checked against its own setup instructions as well.
If a phone or Bluetooth speaker got wet, follow the wet-phone steps or the wet Bluetooth speaker steps first and come back to this test once it is dry and working normally.
What this speaker and audio test checks
The guided stereo sequence moves the same 440 Hz signal from left to both channels, then right while the status names the active step. The balance sweep moves it smoothly left to right and back, which can reveal an abrupt gap, channel swap or route that collapses to mono. The individual controls provide a short routing check, while the Both control sends the same reference to both channels. The frequency buttons play fixed tones for a repeatable listening comparison.
Together these controls can reveal silence, a reversed route or an artifact that repeats, but they do not measure acoustic quality or prove a hardware fault. A perceived off-center position can also come from speaker placement, the room, system balance settings or the listener's position.
This page tests audio output only. It does not request microphone access, record sound, test a microphone or measure hearing. Use the device choices above for laptop or headphone-specific setup without creating separate left/right, stereo or sound-test pages.
How to run this sound test on a phone or tablet
- Move the phone away from your ears and lower its media volume.
- Disconnect wired headphones, Bluetooth earbuds, cars and external speakers.
- Run the guided left-both-right sequence. Note whether audio comes from the phone and whether the channel changes are distinguishable. Repeat an individual channel if needed.
- Play each frequency once. Listen for missing sound, crackling or a large change that repeats at the same hardware volume and phone position.
- Confirm any result with familiar speech or music before changing settings or seeking service.
What the results can mean
No sound from any button
Check media volume and the active audio route. Turn off Silent mode where it affects browser audio, disconnect external devices and retry. If other apps are also silent, use the manufacturer's sound troubleshooting steps.
Left and right sound the same
This can be normal on a phone with one effective output, when Mono Audio is enabled, or when the browser or operating system mixes channels. It does not by itself establish a broken speaker.
One tone buzzes or crackles
Repeat it once at a lower volume and compare with another audio source. A tone can expose distortion, but this page cannot separate debris, liquid, enclosure vibration, software processing or hardware damage. Use the crackling speaker guide for the next checks.
Sound changed after the phone got wet
Stop testing if the device is hot, shows a liquid warning or may be internally wet. Follow the wet-phone safety and drying sequence before deciding whether a water-eject sound is relevant.
How to tell if a phone speaker may be damaged
No browser tone can confirm a torn diaphragm, failed coil, corrosion or another internal fault. The controls above can show a channel or reference tone that sounds different under consistent conditions, such as the same source, volume and phone position, but they cannot diagnose which part failed.
Use the crackling and buzzing guide for the full comparison when distortion is the main symptom, or the muffled and quiet speaker guide when clarity or volume is reduced.
Why this cannot diagnose a speaker
Your phone's model, case, orientation, audio processing and current volume all affect what you hear. Your room and hearing matter too. The browser cannot measure acoustic output without microphone access, and this page deliberately does not request it. Treat the controls as repeatable reference sounds rather than calibrated test equipment.
Official troubleshooting and technical sources
- Apple: If you hear no sound or distorted sound from an iPhone or iPad speaker
- Google: Why can't I hear sound from my Pixel phone?
- Samsung: Speaker does not work properly on a Samsung phone
- Microsoft: Fix Bluetooth connected but no sound in Windows
- Apple: Play iPhone audio on a Bluetooth accessory
- Google: Set up Android Auto while parked
- Google: Listen to media through car speakers with Android Auto
- Apple: Connect iPhone to CarPlay
- MDN: StereoPannerNode
- MDN: OscillatorNode
Testing a computer instead? Use the laptop speaker test. If the goal is a laptop-cleaner sound and its limits, read the laptop speaker cleaner guide.